FAQ: What are 'Event' and 'Result' Types? – ProdataKey, Inc.

ProdataKey allows you to use different conditions for rules and Reports.

'Event' types occur when credentials are used, a hardware event occurs, or certain changes are made in the system

'Result' types occur as a result of an Event in the system.

Event Types

Below are the Event Types available in PDK.io.

AutoOpen Enabled - An Auto-Open schedule began on the door/device.
AutoOpen Disabled - An Auto-Open schedule ended on the door/device.
Credentials Input - A credential (PIN/card/bluetooth/) has been used at the door/device.
Open (DPS) - The door position sensor input detected the door/device was opened
Close (DPS) - The door position sensor input detected the door/device was closed
Request to Exit Open - The request to exit input was triggered on the door/device
Request to Exit Closed - The request to exit input was cleared on the door/device
Propped Alarm - The door propped alarm has triggered for the door/device.
Propped Alarm Clear - The door propped alarm has been cleared for the door/device.
All Prop Clear - All door propped alarms have been cleared.
Forced Alarm - The 'Door Forced' alarm has been triggered for the door/device.
Communication Loss - Communication to the Controller connection has been lost.
Communication Loss Clear - Communication to the Controller connection has been re-established.
Controller Time Unknown - While in Controller Continuity mode, the Controller was unable to validate the current time.
Controller Time Known - While in Controller Continuity mode, the Controller was able to validate the current time after it was unknown.
Known Person - A valid credential, assigned to a person in the system, was used at a door/device.
No Person Associated with Credentials - An unknown credential was used and access was implicitly denied unless allowed by a System Event rule.
Access Denied - A valid credential, assigned to a person in the system, was used at a door/device and access was denied.
Access Allowed on Multiswipe - A valid credential, assigned to a person in the system, was scanned multiple times in rapid succession at a door/device and access was allowed.
Access Allowed - A valid credential, assigned to a person in the system, was used at a door/device and access was allowed.
Duress PIN Entered - A duress PIN was used to authenticate at the reader for a door/device.
Ecard Allowed - While reverted to Ecard usage in Controller Continuity mode, an Ecard was presented at a door/device and allowed.
Ecard Denied - While reverted to Ecard usage in Controller Continuity mode, a non-Ecard credential was presented at a door/device and denied.
Any Duress PIN Entered - When any duress PIN is used to authenticate at the reader for a door/device.
Entity Added - An entity (Person, Group, Connection, etc) was added to the system.
Entity Modified - An entity (Person, Group, Connection, etc) was modified.
Entity Removed - An entity (Person, Group, Connection, etc) was removed/deleted.
Open (Lock) - A door/device was activated/opened/unlocked.
Close (Lock) - A door/device was deactivated/closed/locked.
Try to Open - An activation command was sent to the door/device, either through States or a 3rd-party integration.
Try to Open for Some Time - An activation command, with extended activation time, was sent to the door/device, either through States or a 3rd-party integration.
Do Not Disturb - The “Do Not Disturb” status of the door/device was changed.
Force Toggle - The current state of the door/device was toggled between open/closed and then maintained in the new state.
Forced Alarm Clear - The 'Door Forced' alarm for the door/device has cleared.
Card Scan Error - Bad credential data was received from the card reader connected to the door/device.
Virtual Credentials Input - Virtual credentials, such as the PDK Access app or 3rd part API integration, were used.
Delay Open (Lock) - A Delayed Open (unlock) command was sent to the door/device.
Delay Close (Lock) - A Delayed Close (lock) command was sent to the door/device.
Open/Close (Lock) - The door/device toggled open (unlocked) or closed (locked)
Overcurrent Detected - Excessive/higher than intended current occurred/detected.
Overcurrent Cleared - Standard/intended current occurred/restored.
Input Power Connected - Expected input power is connected/restored.
Input Power Disconnected - Input power is not disconnected/power supply not detected.
Low Power Mode On - Low power mode (low battery charge and no connected power source) was detected for the Controller.
Low Power Mode Off - When low power mode ended for the Controller.
Battery Connected - A battery was connected/detected with a Controller.
Battery Disconnected - A battery was disconnected/lost with a Controller.
Controller Restarted - The Controller was restarted, either by power-cycling/connecting to power, expected reboot from software update, or through a remote action by our Support or engineering teams.
Controller Factory Reset - The Controller was either hard or soft reset through use of the onboard jumpers.
Continuity Expired - Ecard Enforced - The configured 'Time before Ecard fall-back' has been exceeded and Ecard-only operation initiated.
Circuit Breaker On - A flood of logged events (40 events in 30 seconds) occurred on either input A or B (DPS or REX respectively), this disables the input for 30 minutes.
Circuit Breaker Off - A previously triggered Circuit Breaker event ended.
Anti-Passback Violation - An Anti-Passback Violation (a credential previously used for entry was used for entry again without being used for an exit between the events) occurred.
Anti-Passback Clear - An Anti-Passback Violation event expired, as per the Anti-Passback Event Expiration condition.
Credential Reset - A Credential Reset request was sent by an app user.

Results Types

Below are the Filters available for Result Types from Reports that are processed or in Recent Audit Logs.

Known Person - An Person entered into the system used a credential at a door/device
No Person Associated with Credentials - An unknown credential was scanned and access was implicitly denied at a door/device.
Access Denied - A known credential was scanned and access was denied at a door/device.
Access Allowed on Multiswipe - A known credential was scanned and access was allowed with multiple swipes.
Access Allowed - A known credential was scanned and access was allowed.
Send Email - When an email is sent
Do Not Disturb - Toggles the “Do Not Disturb” status of the door/relay. In Do Not Disturb status, the door is locked and unresponsive to regular access attempts until the DND status is toggled again.
Force Toggle - Toggles the current state of the door/relay to open/closed. If a door is closed (locked), toggles to open (unlocked). If the door is open (unlocked), toggles to closed (locked).
Force Open - Holds the door/relay (that the event is created on) in the Open (unlocked) position and will not close (lock) unless Force Closed.
Force Close - A Force Open command was sent to the door/device.
Open - Activate/unlocks/opens the door/device.
Close - Deactivate/locks/closes the door/device.
Lockdown On - Lockdown (doors locked) of selected devices is set to On. All doors are locked.
Lockdown Off - Lockdown (doors locked) of selected devices is set to Off. All doors are unlocked.
Delay Open - A time delay for opening (unlocking) the door/relay
Delay Close - A time delay for closing (locking) the door/relay
Open/Close - Opens (unlocks) the door/relay and sends a close (lock) after a delayed time period